Q(ZY/XY)-2/200 Grade Polyamide Imide Composite Polyester Or Polyesterimide Enameled Copper Round Wire

Product DetailsHuzhou Fuda Electrical Technology Co.,Ltd.

Non-Self-Adhesive Enameled Wire Size (R20)

Conductor nominal diameter / mm	Conductor tolerance / mm	Minimum film thickness / mm			Maximum outer diameter / mm
Conductor nominal diameter / mm	Conductor tolerance / mm	Level 1	Level 2	Level 3	Level 1	Level 2	Level 3
0.018	/	0.002	0.004	/	0.022	0.024	/
0.020		0.002	0.004		0.024	0.027
0.022		0.002	0.005		0.027	0.030
0.025		0.003	0.005		0.031	0.034
0.028		0.003	0.006		0.034	0.038
0.032		0.003	0.007		0.039	0.043
0.036		0.004	0.008		0.044	0.049
0.040		0.004	0.008		0.049	0.054
0.045		0.005	0.010		0.055	0.061
0.050		0.005	0.010		0.060	0.066
0.056		0.006	0.011		0.067	0.074
0.063		0.006	0.012		0.076	0.083
0.071	0.003	0.007	0.012	0.018	0.084	0.091	0.097
0.080	0.003	0.007	0.014	0.020	0.094	0.101	0.108
0.090	0.003	0.008	0.015	0.022	0.105	0.113	0.120
0.100	0.003	0.008	0.016	0.023	0.117	0.125	0.132
0.112	0.003	0.009	0.017	0.026	0.130	0.139	0.147
0.125	0.003	0.010	0.019	0.028	0.144	0.154	0.163
0.140	0.003	0.011	0.021	0.030	0.160	0.171	0.181
0.160	0.003	0.012	0.023	0.033	0.182	0.194	0.205
0.180	0.003	0.013	0.025	0.036	0.204	0.217	0.229
0.200	0.003	0.014	0.027	0.039	0.226	0.239	0.252
0.224	0.003	0.015	0.029	0.043	0.252	0.266	0.280
0.250	0.004	0.017	0.032	0.048	0.281	0.297	0.312
0.280	0.004	0.018	0.033	0.050	0.312	0.329	0.345
0.315	0.004	0.019	0.035	0.053	0.349	0.367	0.384
0.355	0.004	0.020	0.038	0.057	0.392	0.411	0.428
0.400	0.005	0.021	0.040	0.060	0.439	0.459	0.478
0.450	0.005	0.022	0.042	0.064	0.491	0.513	0.533
0.500	0.005	0.024	0.045	0.067	0.544	0.566	0.587
0.560	0.006	0.025	0.047	0.071	0.606	0.630	0.653
0.630	0.006	0.027	0.050	0.075	0.679	0.704	0.728
0.710	0.007	0.028	0.053	0.080	0.762	0.789	0.814
0.800	0.008	0.030	0.056	0.085	0.855	0.884	0.911
0.900	0.009	0.032	0.060	0.090	0.959	0.989	1.018
1.000	0.010	0.034	0.063	0.095	1.062	1.094	1.124
1.120	0.011	0.034	0.065	0.098	1.184	1.217	1.248
1.250	0.013	0.035	0.067	0.100	1.316	1.349	1.381
1.400	0.014	0.036	0.069	0.103	1.468	1.502	1.535
1.600	0.016	0.038	0.071	0.107	1.670	1.706	1.740
1.800	0.018	0.039	0.073	0.110	1.872	1.909	1.944
2.000	0.020	0.040	0.075	0.113	2.074	2.112	2.148
2.240	0.022	0.041	0.077	0.116	2.316	2.355	2.392
2.500	0.025	0.042	0.079	0.119	2.578	2.618	2.656
2.800	0.028	0.043	0.081	0.123	2.880	2.922	2.961
3.150	0.032	0.045	0.084	0.127	3.233	3.276	3.316
3.550	0.036	0.046	0.086	0.130	3.635	3.679	3.721
4.000	0.040	0.047	0.089	0.134	4.088	4.133	4.176
4.500	0.045	0.049	0.092	0.138	4.591	4.637	4.681
5.000	0.050	0.050	0.094	0.142	5.093	5.141	5.186
For the intermediate dimension of the conductor's nominal diameter, the minimum film thickness corresponding to the nominal diameter of the larger conductor shall be taken. Note 1: The minimum outer diameter of 0.063mm and below is calculated according to the conductor diameter + minimum film thickness measured in Table 3. Note 2: The intermediate dimensions of the nominal diameter of the conductors of the R40 series are shown in Appendix A.

Self-Adhesive Enameled Wire Size (R20)

Conductor nominal diameter / mm	Conductor tolerance soil/mm	Inner paint layer minimum and maximum / mm		Self-adhesive layer minimum thickness / mm	Maximum outer diameter / mm
Conductor nominal diameter / mm	Conductor tolerance soil/mm	Level 1B	Level 2B	Self-adhesive layer minimum thickness / mm	Level 1B	Level 2B
0.020	/	0.002	0.004	0.001	0.026	0.029
0.022		0.002	0.004	0.002	0.030	0.033
0.025		0.003	0.005	0.002	0.034	0.037
0.028		0.003	0.006	0.003	0.038	0.042
0.032		0.003	0.006	0.003	0.044	0.048
0.036		0.004	0.007	0.004	0.050	0.055
0.040		0.004	0.008	0.004	0.055	0.060
0.045		0.005	0.009	0.004	0.062	0.068
0.050		0.005	0.010	0.005	0.068	0.074
0.056		0.006	0.011	0.005	0.075	0.082
0.063		0.006	0.012	0.005	0.085	0.092
0.071	0.003	0.007	0.012	0.006	0.094	0.101

Resistance

For enameled wires with conductor nominal diameters of 0.063 mm and below, the resistance at 20 °C shall be within the specified values in Table 3.
For enameled wires with a nominal conductor diameter of 0.063 mm or more, the resistance value is not specified.
After the negotiation between the supplier and the buyer, the enameled wire with a nominal diameter of 0.063mm or more and 1.000mm or less can be used for resistance measurement. In this case, the resistance at 20 °C should be within the range specified in Appendix C.

Conductor nominal diameter / mm	Resistance Ω/m		Conductor nominal diameter / mm	Resistance Ω/m
Conductor nominal diameter / mm	Minimum value	Maximum	Conductor nominal diameter / mm	Minimum value	Maximum
0.013	60.46	73.89	0.036	15.16	18.42
0.020	48.97	59.85	0.040	12.28	14.92
0.022	40.47	49.47	0.045	9.705	11.79
0.025	31.34	38.31	0.050	7.922	9.489
0.023	24.99	30.54	0.056	6.316	7.565
0.032	19.13	23.38	0.063	5.045	5.922
Note 1: The above specified values are calculated according to Appendix B. Note 2: See Appendix C for nominal resistance.

Elongation

The elongation at break shall not be less than the value specified in Table 4.
GB / T6109.1-2008 / IEC60317-0-1:2005

Conductor nominal diameter / mm	Minimum elongation / %	Conductor nominal diameter / mm	Minimum elongation / %	Conductor nominal diameter / mm	Minimum elongation / %
0.018	5	0.180	20	1.800	32
0.020	6	0.200	21	2.000	33
0.022	6	0.224	21	2.240	33
0.025	7	0.250	22	2.500	33
0.028	7	0.280	22	2.800	34
0.032	8	0.315	23	3.150	34
0.036	8	0.355	23	3.550	35
0.040	9	0.400	24	4.000	35
0.045	9	0.450	25	4.500	36
0.050	10	0.500	25	5.000	36
0.056	10	0.560	26	/	/
0.063	12	0.630	27
0.071	13	0.710	28
0.080	14	0.800	28
0.090	15	0.900	29
0.100	16	1.000	30
0.112	17	1.120	30
0.125	17	1.250	31
0.140	18	1.400	32
0.160	19	1.600	32
Note: For the intermediate dimension of the conductor's nominal diameter, the elongation value corresponding to the nominal diameter of the larger conductor shall be taken.

Resilience

When the conductor has a nominal diameter of 0.080 mm and above and 1.600 mm or less, the maximum rebound angle of the enameled wire shall not exceed the value specified in Table 5 when tested on a specified round bar with a specified load.
The maximum rebound angle of the enameled wire with a nominal conductor diameter of 1.600 mm or more shall not exceed 5 °.

Conductor nominal diameter / mm	Round rod diameter / mm	Load / N	Maximum rebound angle / (°)
Conductor nominal diameter / mm	Round rod diameter / mm	Load / N	Level 1	Level 2 and Level 1B	Level 3 and Level 2B
0.080	5	0.25	70	80	100
0.090			67	77	94
0.100			64	73	90
0.112	7	0.50	64	73	88
0.125			62	70	84
0.340			59	67	79
0.160	10	1.0	59	67	78
0.180			57	65	75
0.200			54	62	72
0.224	12.5	2.0	51	59	68
0.250			49	56	65
0.280			47	53	61
0.315	19	4.0	50	55	62
0.355			48	53	59
0.400			45	50	55
0.450	25	8.0	44	48	53
0.5C0			43	47	51
0.560			41	44	48
0.630	37.5	12.0	46	50	53
0.710			44	47	50
0.800			41	43	46
0.900	50	15.0	45	48	51
1.000			42	45	47
1.120			39	41	43
1.250			35	37	39
1.400			32	34	36
1.600			28	30	32
Note: For the intermediate dimension of the nominal diameter of the conductor, the value of the rebound angle corresponding to the nominal diameter of the larger conductor should be taken.

Flexibility And Adhesion

Round bar winding test (conductor nominal diameter 1.600mm and below)
After the enameled wire is stretched as specified in Table 6 and wound on a suitable round bar, the paint layer shall not crack.